87 lines
3.0 KiB
Python
87 lines
3.0 KiB
Python
|
# hardware/inverter.py
|
|||
|
|
from pymodbus.exceptions import ModbusException
|
|||
|
|
|
|||
|
|
|
|||
|
|
class InverterController:
|
|||
|
|
def __init__(self, relay_controller):
|
|||
|
|
self.relay_controller = relay_controller
|
|||
|
|
self.max_frequency = 400.0 # 频率最大值
|
|||
|
|
|
|||
|
|
# 变频器配置
|
|||
|
|
self.config = {
|
|||
|
|
'slave_id': 1,
|
|||
|
|
'frequency_register': 0x01, # 2001H
|
|||
|
|
'start_register': 0x00, # 2000H
|
|||
|
|
'stop_register': 0x00, # 2000H（用于停机）
|
|||
|
|
'start_command': 0x0013, # 正转点动运行
|
|||
|
|
'stop_command': 0x0001 # 停机
|
|||
|
|
}
|
|||
|
|
|
|||
|
|
def set_frequency(self, frequency):
|
|||
|
|
"""设置变频器频率"""
|
|||
|
|
try:
|
|||
|
|
if not self.relay_controller.modbus_client.connect():
|
|||
|
|
print("无法连接网络继电器Modbus服务")
|
|||
|
|
return False
|
|||
|
|
|
|||
|
|
# 使用最大频率变量计算百分比
|
|||
|
|
percentage = frequency / self.max_frequency # 得到 0~1 的比例
|
|||
|
|
value = int(percentage * 10000) # 转换为 -10000 ~ 10000 的整数
|
|||
|
|
|
|||
|
|
# 限制范围
|
|||
|
|
value = max(-10000, min(10000, value))
|
|||
|
|
|
|||
|
|
result = self.relay_controller.modbus_client.write_register(
|
|||
|
|
self.config['frequency_register'],
|
|||
|
|
value,
|
|||
|
|
slave=self.config['slave_id']
|
|||
|
|
)
|
|||
|
|
|
|||
|
|
if isinstance(result, Exception):
|
|||
|
|
print(f"设置频率失败: {result}")
|
|||
|
|
return False
|
|||
|
|
|
|||
|
|
print(f"设置变频器频率为 {frequency}Hz")
|
|||
|
|
return True
|
|||
|
|
except ModbusException as e:
|
|||
|
|
print(f"变频器Modbus通信错误: {e}")
|
|||
|
|
return False
|
|||
|
|
finally:
|
|||
|
|
self.relay_controller.modbus_client.close()
|
|||
|
|
|
|||
|
|
def control(self, action):
|
|||
|
|
"""控制变频器启停"""
|
|||
|
|
try:
|
|||
|
|
if not self.relay_controller.modbus_client.connect():
|
|||
|
|
print("无法连接网络继电器Modbus服务")
|
|||
|
|
return False
|
|||
|
|
|
|||
|
|
if action == 'start':
|
|||
|
|
result = self.relay_controller.modbus_client.write_register(
|
|||
|
|
address=self.config['start_register'],
|
|||
|
|
value=self.config['start_command'],
|
|||
|
|
slave=self.config['slave_id']
|
|||
|
|
)
|
|||
|
|
print("启动变频器")
|
|||
|
|
elif action == 'stop':
|
|||
|
|
result = self.relay_controller.modbus_client.write_register(
|
|||
|
|
address=self.config['start_register'],
|
|||
|
|
value=self.config['stop_command'],
|
|||
|
|
slave=self.config['slave_id']
|
|||
|
|
)
|
|||
|
|
print("停止变频器")
|
|||
|
|
else:
|
|||
|
|
print(f"无效操作: {action}")
|
|||
|
|
return False
|
|||
|
|
|
|||
|
|
if isinstance(result, Exception):
|
|||
|
|
print(f"控制失败: {result}")
|
|||
|
|
return False
|
|||
|
|
|
|||
|
|
return True
|
|||
|
|
except ModbusException as e:
|
|||
|
|
print(f"变频器控制错误: {e}")
|
|||
|
|
return False
|
|||
|
|
finally:
|
|||
|
|
self.relay_controller.modbus_client.close()
|