main是测试过的移动到初始点再直线的代码
This commit is contained in:
琉璃月光
489
main.py
489
main.py
@ -13,8 +13,7 @@ plt.rcParams['font.sans-serif'] = ['SimHei', 'WenQuanYi Zen Hei', 'FangSong']
|
||||
plt.rcParams['axes.unicode_minus'] = False
|
||||
|
||||
# ------------------------ 调试开关 ------------------------
|
||||
#DEBUG_MODE = False # <<< 设为 False 控制真实电机
|
||||
DEBUG_MODE = True # <<< 设为 False 控制真实电机
|
||||
DEBUG_MODE = False # <<< 设为 False 控制真实电机
|
||||
|
||||
# 导入运动学和轨迹函数（确保路径正确）
|
||||
try:
|
||||
@ -90,35 +89,15 @@ def init_motors():
|
||||
|
||||
if DEBUG_MODE:
|
||||
print("【DEBUG】跳过电机初始化")
|
||||
# 给个简单的 mock，包含 getPosition 接口（返回度数）
|
||||
class MockMotor:
|
||||
def __init__(self):
|
||||
self._pos_deg = 90.0 # 默认为 90°（即偏移后的值）
|
||||
def getPosition(self):
|
||||
return self._pos_deg
|
||||
def setPosition(self, deg):
|
||||
self._pos_deg = deg
|
||||
|
||||
motor1 = MockMotor()
|
||||
motor2 = MockMotor()
|
||||
class MockControl:
|
||||
def enable(self, m): return True
|
||||
def disable(self, m): return None
|
||||
def controlMIT(self, m, kp, kd, pos, vel, torq):
|
||||
# pos 为弧度，记录到mock motor（用于DEBUG可视化一致性）
|
||||
try:
|
||||
deg = np.degrees(pos + np.pi/2) # 因为 motor 的 getPosition 返回带偏移的度值
|
||||
if m is motor1:
|
||||
motor1.setPosition(deg)
|
||||
elif m is motor2:
|
||||
motor2.setPosition(deg)
|
||||
except:
|
||||
pass
|
||||
return None
|
||||
def refresh_motor_status(self, m): return None
|
||||
def switchControlMode(self, m, mode): return None
|
||||
def save_motor_param(self, m): return None
|
||||
motor_control = MockControl()
|
||||
motor1 = motor2 = type('Motor', (), {'id': 0})()
|
||||
motor_control = type('MotorControl', (), {
|
||||
'enable': lambda x: True,
|
||||
'disable': lambda x: None,
|
||||
'controlMIT': lambda m, kp, kd, pos, vel, torq: None,
|
||||
'refresh_motor_status': lambda m: None,
|
||||
'switchControlMode': lambda m, mode: None,
|
||||
'save_motor_param': lambda m: None
|
||||
})()
|
||||
return motor1, motor2, motor_control
|
||||
|
||||
try:
|
||||
@ -144,14 +123,32 @@ def init_motors():
|
||||
print("电机已使能。")
|
||||
return motor1, motor2, motor_control
|
||||
|
||||
# ------------------------ MIT 控制函数 ------------------------
|
||||
# 电机1、4安全角度范围（弧度）
|
||||
THETA1_MIN = -np.pi/2 # -60°
|
||||
THETA1_MAX = np.pi/2 # 60°
|
||||
THETA4_MIN = -np.pi/2 # -60°
|
||||
THETA4_MAX = np.pi/2 # 60°
|
||||
|
||||
# ------------------------ MIT 控制函数（带限位 + 回零逻辑） ------------------------
|
||||
def control_two_motors_mit(theta1_rad, theta4_rad):
|
||||
"""
|
||||
发送 MIT 控制指令（角度单位：弧度）
|
||||
参数: theta1_rad, theta4_rad —— 目标角度（弧度），这里 theta 已去除 ANGLE_OFFSET_RAD
|
||||
带限位检测：如果超限，自动触发回零。
|
||||
"""
|
||||
global current_theta1, current_theta4
|
||||
|
||||
# --- 限位检测 ---
|
||||
if not (THETA1_MIN <= theta1_rad <= THETA1_MAX):
|
||||
print(f"θ1 超出限位 [{THETA1_MIN}, {THETA1_MAX}]，执行回零...")
|
||||
move_motors_to_zero()
|
||||
return
|
||||
|
||||
if not (THETA4_MIN <= theta4_rad <= THETA4_MAX):
|
||||
print(f"θ4 超出限位 [{THETA4_MIN}, {THETA4_MAX}]，执行回零...")
|
||||
move_motors_to_zero()
|
||||
return
|
||||
|
||||
# --- 正常控制 ---
|
||||
pos1 = theta1_rad
|
||||
pos4 = theta4_rad
|
||||
vel = 0.1
|
||||
@ -161,174 +158,69 @@ def control_two_motors_mit(theta1_rad, theta4_rad):
|
||||
motor_control.controlMIT(motor1, KP, KD, pos1, vel, torq)
|
||||
motor_control.controlMIT(motor2, KP, KD, pos4, vel, torq)
|
||||
else:
|
||||
# DEBUG 模式：打印并更新 mock motor（mock control 已在 init 中实现）
|
||||
print(f"[DEBUG] 控制 -> θ1={np.degrees(theta1_rad):.2f}°, θ4={np.degrees(theta4_rad):.2f}°")
|
||||
motor_control.controlMIT(motor1, KP, KD, pos1, vel, torq)
|
||||
motor_control.controlMIT(motor2, KP, KD, pos4, vel, torq)
|
||||
|
||||
current_theta1 = theta1_rad
|
||||
current_theta4 = theta4_rad
|
||||
|
||||
# ------------------------ 平滑移动到起点（插值过渡）------------------------
|
||||
def move_to_start_interpolated(start_x, start_y, steps=60, dt=DT):
|
||||
"""
|
||||
从电机当前位置平滑插值过渡到轨迹起点
|
||||
返回：time_log_pre, theta1_log_pre, theta4_log_pre, x_fk_log_pre, y_fk_log_pre
|
||||
"""
|
||||
ANGLE_OFFSET_RAD = np.pi / 2
|
||||
|
||||
# 计算目标角度（逆解）
|
||||
try:
|
||||
theta1_target_raw, theta4_target_raw = inverseF(start_x, start_y, L1, L2, L3, L4, L0)
|
||||
theta1_target = float(theta1_target_raw) - ANGLE_OFFSET_RAD
|
||||
theta4_target = float(theta4_target_raw) - ANGLE_OFFSET_RAD
|
||||
except Exception as e:
|
||||
print(f"起点逆解失败: {e}")
|
||||
return [], [], [], [], []
|
||||
|
||||
# 获取当前电机角度（转换为去偏移的弧度值）
|
||||
if not DEBUG_MODE:
|
||||
try:
|
||||
motor_control.refresh_motor_status(motor1)
|
||||
motor_control.refresh_motor_status(motor2)
|
||||
time.sleep(0.05)
|
||||
pos1_deg = motor1.getPosition() # 电机读数通常为度（含偏移）
|
||||
pos2_deg = motor2.getPosition()
|
||||
current_theta1 = np.radians(pos1_deg) - ANGLE_OFFSET_RAD
|
||||
current_theta4 = np.radians(pos2_deg) - ANGLE_OFFSET_RAD
|
||||
except Exception as e:
|
||||
print(f"读取电机当前位置失败: {e}; 使用默认 0")
|
||||
current_theta1 = current_theta4 = 0.0
|
||||
else:
|
||||
# DEBUG 下使用 mock motor 的 getPosition（init 已设置）
|
||||
try:
|
||||
pos1_deg = motor1.getPosition()
|
||||
pos2_deg = motor2.getPosition()
|
||||
current_theta1 = np.radians(pos1_deg) - ANGLE_OFFSET_RAD
|
||||
current_theta4 = np.radians(pos2_deg) - ANGLE_OFFSET_RAD
|
||||
except:
|
||||
current_theta1 = current_theta4 = 0.0
|
||||
|
||||
# 生成插值序列（考虑角度连续性）
|
||||
theta1_target = adjust_angle_continuity(theta1_target, current_theta1)
|
||||
theta4_target = adjust_angle_continuity(theta4_target, current_theta4)
|
||||
theta1_list = np.linspace(current_theta1, theta1_target, steps)
|
||||
theta4_list = np.linspace(current_theta4, theta4_target, steps)
|
||||
|
||||
# 日志
|
||||
time_log = []
|
||||
theta1_log = []
|
||||
theta4_log = []
|
||||
x_fk_log = []
|
||||
y_fk_log = []
|
||||
|
||||
print(f"平滑移动到起点 -> θ1_target={np.degrees(theta1_target):.2f}°, θ4_target={np.degrees(theta4_target):.2f}° (steps={steps})")
|
||||
|
||||
start_t = perf_counter()
|
||||
l1, l2, l3, l4, l5 = L1, L2, L3, L4, L0
|
||||
omega1 = omega4 = 0.0
|
||||
alpha1 = alpha4 = 0.0
|
||||
|
||||
for t1, t4 in zip(theta1_list, theta4_list):
|
||||
# 发送控制
|
||||
control_two_motors_mit(float(t1), float(t4))
|
||||
|
||||
# FK 验证（使用带偏移角度）
|
||||
try:
|
||||
xc, yc, *_ = forwardF(
|
||||
u1=float(t1 + ANGLE_OFFSET_RAD),
|
||||
u4=float(t4 + ANGLE_OFFSET_RAD),
|
||||
omega1=omega1, omega4=omega4,
|
||||
l1=l1, l2=l2, l3=l3, l4=l4, l5=l5,
|
||||
alpha1=alpha1, alpha4=alpha4
|
||||
)
|
||||
except Exception:
|
||||
xc, yc = np.nan, np.nan
|
||||
|
||||
elapsed = perf_counter() - start_t
|
||||
time_log.append(elapsed)
|
||||
theta1_log.append(np.degrees(float(t1))) # 记录发送给电机的角度（度）
|
||||
theta4_log.append(np.degrees(float(t4)))
|
||||
x_fk_log.append(xc)
|
||||
y_fk_log.append(yc)
|
||||
|
||||
busy_wait(dt)
|
||||
|
||||
return time_log, theta1_log, theta4_log, x_fk_log, y_fk_log
|
||||
|
||||
# ------------------------ 直接轨迹执行函数（无插值）------------------------
|
||||
from time import perf_counter
|
||||
import numpy as np
|
||||
|
||||
|
||||
def execute_direct_trajectory(x_list_in, y_list_in, dt=DT):
|
||||
# 假设其他所需函数和全局变量已定义，例如 inverseF, forwardF, adjust_angle_continuity, control_two_motors_mit, 等等.
|
||||
|
||||
def execute_direct_trajectory(x_list, y_list, dt=DT):
|
||||
"""
|
||||
直接执行轨迹：对每个 (x,y) 计算逆解并立即发送角度，不做任何插值或速度规划
|
||||
直接执行轨迹：对每个 (x,y) 计算逆解并立即发送角度，不做插值或速度规划
|
||||
执行前：先把电机从零点平滑移动到轨迹起点
|
||||
返回: (time_log, theta1_log, theta4_log, x_fk_log, y_fk_log)
|
||||
"""
|
||||
global motor_control, motor1, motor2
|
||||
|
||||
# 定义90度对应于弧度的偏移量
|
||||
ANGLE_OFFSET_RAD = np.pi / 2 # 即90度对应的弧度值
|
||||
|
||||
time_log = []
|
||||
theta1_log = []
|
||||
theta4_log = []
|
||||
x_fk_log = []
|
||||
y_fk_log = []
|
||||
ANGLE_OFFSET_RAD = np.pi / 2 # 90° 偏移量
|
||||
|
||||
time_log, theta1_log, theta4_log, x_fk_log, y_fk_log = [], [], [], [], []
|
||||
l1, l2, l3, l4, l5 = L1, L2, L3, L4, L0
|
||||
omega1 = omega4 = 0.0
|
||||
alpha1 = alpha4 = 0.0
|
||||
|
||||
# 获取当前角度（用于连续性调整）
|
||||
if not DEBUG_MODE:
|
||||
try:
|
||||
motor_control.refresh_motor_status(motor1)
|
||||
motor_control.refresh_motor_status(motor2)
|
||||
time.sleep(0.1)
|
||||
motor_control.refresh_motor_status(motor1)
|
||||
motor_control.refresh_motor_status(motor2)
|
||||
current_theta1 = np.radians(motor1.getPosition()) - ANGLE_OFFSET_RAD
|
||||
current_theta4 = np.radians(motor2.getPosition()) - ANGLE_OFFSET_RAD
|
||||
except Exception:
|
||||
# 若读取失败则以前次 global 值或 0 为准
|
||||
current_theta1 = current_theta4 = 0.0
|
||||
else:
|
||||
# DEBUG 下 mock motor 初始已设置为 90deg，减偏移得到 0
|
||||
try:
|
||||
current_theta1 = np.radians(motor1.getPosition()) - ANGLE_OFFSET_RAD
|
||||
current_theta4 = np.radians(motor2.getPosition()) - ANGLE_OFFSET_RAD
|
||||
except Exception:
|
||||
current_theta1 = current_theta4 = 0.0
|
||||
# --- 轨迹起点逆解 ---
|
||||
x0, y0 = x_list[0], y_list[0]
|
||||
try:
|
||||
raw_theta1, raw_theta4 = inverseF(x0, y0, L1, L2, L3, L4, L0)
|
||||
theta1_start = float(raw_theta1) - ANGLE_OFFSET_RAD
|
||||
theta4_start = float(raw_theta4) - ANGLE_OFFSET_RAD
|
||||
print(f"起点逆解成功 -> θ1={np.degrees(theta1_start):.2f}°, θ4={np.degrees(theta4_start):.2f}°")
|
||||
except Exception as e:
|
||||
print(f"❌ 起点逆解失败: {e}")
|
||||
return [], [], [], [], []
|
||||
|
||||
# --- 电机移动到起点 ---
|
||||
print("电机从零点移动到轨迹起点...")
|
||||
move_motors_to_target(theta1_start, theta4_start, duration=1.5, dt=dt)
|
||||
current_theta1, current_theta4 = theta1_start, theta4_start
|
||||
|
||||
# --- 轨迹执行 ---
|
||||
start_time = perf_counter()
|
||||
|
||||
for i, (x, y) in enumerate(zip(x_list_in, y_list_in)):
|
||||
for i, (x, y) in enumerate(zip(x_list, y_list)):
|
||||
try:
|
||||
# 计算逆解
|
||||
raw_theta1, raw_theta4 = inverseF(x, y, L1, L2, L3, L4, L0)
|
||||
|
||||
# 应用角度偏移
|
||||
target_theta1 = float(raw_theta1) - ANGLE_OFFSET_RAD
|
||||
target_theta4 = float(raw_theta4) - ANGLE_OFFSET_RAD
|
||||
|
||||
# 调整角度连续性
|
||||
target_theta1 = adjust_angle_continuity(target_theta1, current_theta1)
|
||||
target_theta4 = adjust_angle_continuity(target_theta4, current_theta4)
|
||||
|
||||
except Exception as e:
|
||||
print(f"第 {i} 点逆解失败 ({x:.2f}, {y:.2f}): {e}")
|
||||
# 保持上一角度
|
||||
target_theta1 = current_theta1
|
||||
target_theta4 = current_theta4
|
||||
target_theta1, target_theta4 = current_theta1, current_theta4
|
||||
else:
|
||||
current_theta1, current_theta4 = target_theta1, target_theta4
|
||||
|
||||
# === 直接发送角度到电机（假设motor api接受弧度值）===
|
||||
# 控制电机
|
||||
control_two_motors_mit(target_theta1, target_theta4)
|
||||
|
||||
# === FK 验证实际到达位置 ===
|
||||
# FK 验证
|
||||
try:
|
||||
xc, yc, *_ = forwardF(
|
||||
u1=target_theta1 + ANGLE_OFFSET_RAD,
|
||||
@ -339,21 +231,21 @@ def execute_direct_trajectory(x_list_in, y_list_in, dt=DT):
|
||||
)
|
||||
x_fk_log.append(xc)
|
||||
y_fk_log.append(yc)
|
||||
except Exception:
|
||||
except:
|
||||
x_fk_log.append(np.nan)
|
||||
y_fk_log.append(np.nan)
|
||||
|
||||
# 记录日志
|
||||
elapsed = perf_counter() - start_time
|
||||
time_log.append(elapsed)
|
||||
theta1_log.append(np.degrees(target_theta1)) # 将弧度转回角度以便记录（电机实际角度）
|
||||
theta1_log.append(np.degrees(target_theta1))
|
||||
theta4_log.append(np.degrees(target_theta4))
|
||||
|
||||
# 固定延时，控制发送频率
|
||||
busy_wait(dt)
|
||||
|
||||
return time_log, theta1_log, theta4_log, x_fk_log, y_fk_log
|
||||
|
||||
|
||||
# ------------------------ 动画绘制函数 ------------------------
|
||||
def draw_frame(i):
|
||||
x = x_list[i]
|
||||
@ -367,7 +259,7 @@ def draw_frame(i):
|
||||
x_coords = [0, x2, x, x4, L0]
|
||||
y_coords = [0, y2, y, y4, 0]
|
||||
line.set_data(x_coords, y_coords)
|
||||
except Exception:
|
||||
except:
|
||||
line.set_data([], [])
|
||||
return line,
|
||||
|
||||
@ -379,13 +271,6 @@ def run_trajectory_with_animation(trajectory_func, **params):
|
||||
x_list, y_list = trajectory_func(**params)
|
||||
print(f"轨迹点数: {len(x_list)}")
|
||||
|
||||
if len(x_list) == 0:
|
||||
print("轨迹点为空，退出。")
|
||||
return
|
||||
|
||||
# --- 平滑移动到轨迹起点（插值过渡），并收集 pre-move 日志 ---
|
||||
t_pre, th1_pre, th4_pre, xfk_pre, yfk_pre = move_to_start_interpolated(x_list[0], y_list[0], steps=60, dt=DT)
|
||||
|
||||
# --- 动画 ---
|
||||
fig, ax = plt.subplots(figsize=(10, 8))
|
||||
ax.set_xlim(-50, L0 + 100)
|
||||
@ -398,62 +283,25 @@ def run_trajectory_with_animation(trajectory_func, **params):
|
||||
line, = ax.plot([], [], 'r-o', lw=3, ms=6, label='机械臂')
|
||||
ax.legend()
|
||||
|
||||
ani = FuncAnimation(fig, draw_frame, frames=len(x_list), interval=50, blit=True, repeat=False)
|
||||
ani = FuncAnimation(fig, draw_frame, frames=len(x_list),
|
||||
interval=50, blit=True, repeat=False)
|
||||
plt.show()
|
||||
|
||||
# --- 执行并记录（正向）---
|
||||
print("开始执行轨迹（正向）...")
|
||||
t_fwd, th1_fwd, th4_fwd, xfk_fwd, yfk_fwd = execute_direct_trajectory(x_list, y_list, dt=DT)
|
||||
# --- 执行并记录 ---
|
||||
print("开始执行轨迹（直接发送角度）...")
|
||||
time_log, theta1_log, theta4_log, x_fk_log, y_fk_log = execute_direct_trajectory(
|
||||
x_list, y_list, dt=DT # 每个点发送后延时 1ms，这个地方控制电机延时
|
||||
)
|
||||
|
||||
# --- 执行并记录（反向）---
|
||||
print("开始执行轨迹（反向）...")
|
||||
t_rev, th1_rev, th4_rev, xfk_rev, yfk_rev = execute_direct_trajectory(x_list[::-1], y_list[::-1], dt=DT)
|
||||
|
||||
# --- 合并三个阶段的数据（仅用于角度时间线显示） ---
|
||||
time_offset = 0.0
|
||||
all_time = []
|
||||
all_th1 = []
|
||||
all_th4 = []
|
||||
all_xfk = []
|
||||
all_yfk = []
|
||||
|
||||
# add pre
|
||||
for dt0, a, b, c, d in zip(t_pre, th1_pre, th4_pre, xfk_pre, yfk_pre):
|
||||
all_time.append(time_offset + dt0)
|
||||
all_th1.append(a)
|
||||
all_th4.append(b)
|
||||
all_xfk.append(c)
|
||||
all_yfk.append(d)
|
||||
if len(t_pre) > 0:
|
||||
time_offset = all_time[-1]
|
||||
|
||||
# add fwd (shifted)
|
||||
for dt0, a, b, c, d in zip(t_fwd, th1_fwd, th4_fwd, xfk_fwd, yfk_fwd):
|
||||
all_time.append(time_offset + dt0 + DT)
|
||||
all_th1.append(a)
|
||||
all_th4.append(b)
|
||||
all_xfk.append(c)
|
||||
all_yfk.append(d)
|
||||
if len(t_fwd) > 0:
|
||||
time_offset = all_time[-1]
|
||||
|
||||
# add rev (shifted)
|
||||
for dt0, a, b, c, d in zip(t_rev, th1_rev, th4_rev, xfk_rev, yfk_rev):
|
||||
all_time.append(time_offset + dt0 + DT)
|
||||
all_th1.append(a)
|
||||
all_th4.append(b)
|
||||
all_xfk.append(c)
|
||||
all_yfk.append(d)
|
||||
|
||||
# --- 绘制关节角度（包含预定位） ---
|
||||
# --- 绘制关节角度 ---
|
||||
fig2, (ax1, ax2) = plt.subplots(2, 1, figsize=(10, 6), sharex=True)
|
||||
ax1.plot(all_time, all_th1, 'b-o', markersize=3, linewidth=1.0, label='θ₁ (电机1)')
|
||||
ax1.plot(time_log, theta1_log, 'b-o', markersize=3, linewidth=1.5, label='θ₁ (电机1)')
|
||||
ax1.set_ylabel('关节角 θ₁ (°)')
|
||||
ax1.set_title('电机关节角度随时间变化（含预定位 + 正向 + 反向）')
|
||||
ax1.set_title('电机关节角度随时间变化')
|
||||
ax1.grid(True, alpha=0.5)
|
||||
ax1.legend()
|
||||
|
||||
ax2.plot(all_time, all_th4, 'r-o', markersize=3, linewidth=1.0, label='θ₄ (电机2)')
|
||||
ax2.plot(time_log, theta4_log, 'r-o', markersize=3, linewidth=1.5, label='θ₄ (电机2)')
|
||||
ax2.set_xlabel('时间 (秒)')
|
||||
ax2.set_ylabel('关节角 θ₄ (°)')
|
||||
ax2.grid(True, alpha=0.5)
|
||||
@ -461,80 +309,157 @@ def run_trajectory_with_animation(trajectory_func, **params):
|
||||
plt.tight_layout()
|
||||
plt.show()
|
||||
|
||||
# --- FK 验证（只使用正向段；若需要也绘制反向段）---
|
||||
# --- FK 验证 ---
|
||||
fig3, ax3 = plt.subplots(figsize=(10, 8))
|
||||
ax3.plot(x_list, y_list, 'b--', linewidth=2, label='目标轨迹', alpha=0.8)
|
||||
|
||||
# 正向 FK（对比目标）
|
||||
if len(xfk_fwd) > 0:
|
||||
ax3.plot(xfk_fwd, yfk_fwd, 'g-', linewidth=2, marker='o', markersize=3, label='FK 重建轨迹（正向）', alpha=0.8)
|
||||
# 标注正向起点/终点（若存在有效点）
|
||||
valid_idx = [i for i, (xx, yy) in enumerate(zip(xfk_fwd, yfk_fwd)) if not (np.isnan(xx) or np.isnan(yy))]
|
||||
if len(valid_idx) > 0:
|
||||
ax3.scatter(xfk_fwd[valid_idx[0]], yfk_fwd[valid_idx[0]], c='green', s=100, marker='s', label='正向起点')
|
||||
ax3.scatter(xfk_fwd[valid_idx[-1]], yfk_fwd[valid_idx[-1]], c='lime', s=100, marker='x', label='正向终点')
|
||||
|
||||
# 反向 FK（对比反向目标）
|
||||
if len(xfk_rev) > 0:
|
||||
# xfk_rev 对应的是 x_list[::-1]
|
||||
ax3.plot(xfk_rev, yfk_rev, 'm-', linewidth=1.5, marker='x', markersize=3, label='FK 重建轨迹（反向）', alpha=0.7)
|
||||
|
||||
ax3.plot(x_fk_log, y_fk_log, 'g-', linewidth=2, marker='o', markersize=3, label='FK 重建轨迹', alpha=0.7)
|
||||
ax3.scatter(x_fk_log[0], y_fk_log[0], c='green', s=100, marker='s', label='起点')
|
||||
ax3.scatter(x_fk_log[-1], y_fk_log[-1], c='red', s=100, marker='x', label='终点')
|
||||
ax3.set_xlabel('X (mm)')
|
||||
ax3.set_ylabel('Y (mm)')
|
||||
ax3.set_title('FK 验证：目标 vs 实际轨迹（不包含预定位段）')
|
||||
ax3.set_title('FK 验证：目标 vs 实际轨迹')
|
||||
ax3.grid(True, alpha=0.5)
|
||||
ax3.legend()
|
||||
ax3.set_aspect('equal', adjustable='box')
|
||||
ax3.set_aspect('equal')
|
||||
plt.tight_layout()
|
||||
plt.show()
|
||||
|
||||
# --- 误差统计（仅统计正向段的误差，与目标 x_list/y_list 对比） ---
|
||||
mask = ~np.isnan(xfk_fwd) & ~np.isnan(yfk_fwd)
|
||||
if np.sum(mask) == 0:
|
||||
print("【警告】正向段 FK 数据全为 nan，无法计算误差")
|
||||
else:
|
||||
# --- 误差统计 ---
|
||||
mask = ~np.isnan(x_fk_log) & ~np.isnan(y_fk_log)
|
||||
x_fk_valid = np.array(x_fk_log)[mask]
|
||||
y_fk_valid = np.array(y_fk_log)[mask]
|
||||
if len(x_fk_valid) == 0:
|
||||
print("【警告】FK 数据全为 nan，无法计算误差")
|
||||
return
|
||||
|
||||
# 插值对齐长度
|
||||
t_target = np.linspace(0, 1, len(x_list))
|
||||
t_fk = np.linspace(0, 1, len(x_fk_valid))
|
||||
from scipy.interpolate import interp1d
|
||||
try:
|
||||
f_x = interp1d(t_fk, x_fk_valid, kind='linear', fill_value='extrapolate')
|
||||
f_y = interp1d(t_fk, y_fk_valid, kind='linear', fill_value='extrapolate')
|
||||
x_interp = f_x(t_target)
|
||||
y_interp = f_y(t_target)
|
||||
errors = np.sqrt((x_interp - x_list)**2 + (y_interp - y_list)**2)
|
||||
print("\n=== FK 验证误差统计 ===")
|
||||
print(f"平均误差: {np.mean(errors):.3f} mm")
|
||||
print(f"最大误差: {np.max(errors):.3f} mm")
|
||||
print(f"标准差: {np.std(errors):.3f} mm")
|
||||
except Exception as e:
|
||||
print(f"误差计算失败: {e}")
|
||||
|
||||
# --- 关节角度范围 ---
|
||||
print("\n=== 关节角度范围统计 ===")
|
||||
print(f"θ₁ 范围: {min(theta1_log):.2f}° ~ {max(theta1_log):.2f}°")
|
||||
print(f"θ₄ 范围: {min(theta4_log):.2f}° ~ {max(theta4_log):.2f}°")
|
||||
|
||||
# ==================== 获取电机当前位置 =====================
|
||||
def get_current_motor_position():
|
||||
"""
|
||||
获取当前电机角度（电机原始单位，通常是度），并打印。
|
||||
返回：theta1_current, theta4_current（度）
|
||||
"""
|
||||
if not DEBUG_MODE:
|
||||
try:
|
||||
valid_x = np.array(xfk_fwd)[mask]
|
||||
valid_y = np.array(yfk_fwd)[mask]
|
||||
# 用线性插值重采样 valid 序列到目标轨迹长度
|
||||
from scipy.interpolate import interp1d
|
||||
t_fk = np.linspace(0, 1, len(valid_x))
|
||||
f_x = interp1d(t_fk, valid_x, kind='linear', fill_value='extrapolate')
|
||||
f_y = interp1d(t_fk, valid_y, kind='linear', fill_value='extrapolate')
|
||||
t_target = np.linspace(0, 1, len(x_list))
|
||||
x_interp = f_x(t_target)
|
||||
y_interp = f_y(t_target)
|
||||
errors = np.sqrt((x_interp - x_list)**2 + (y_interp - y_list)**2)
|
||||
print("\n=== FK 验证误差统计（仅正向段） ===")
|
||||
print(f"平均误差: {np.mean(errors):.3f} mm")
|
||||
print(f"最大误差: {np.max(errors):.3f} mm")
|
||||
print(f"标准差: {np.std(errors):.3f} mm")
|
||||
except Exception as e:
|
||||
print(f"误差计算失败: {e}")
|
||||
motor_control.refresh_motor_status(motor1)
|
||||
motor_control.refresh_motor_status(motor2)
|
||||
time.sleep(0.05)
|
||||
theta1_current = motor1.getPosition()
|
||||
theta4_current = motor2.getPosition()
|
||||
except Exception:
|
||||
theta1_current = theta4_current = 0.0
|
||||
else:
|
||||
theta1_current = motor1.getPosition()
|
||||
theta4_current = motor2.getPosition()
|
||||
|
||||
print(f"当前电机弧度 -> θ1={theta1_current:.2f}, θ4={theta4_current:.2f}")
|
||||
return theta1_current, theta4_current
|
||||
|
||||
# ==================== MIT 模式回零函数 =====================
|
||||
def move_motors_to_zero(duration=1.0, dt=DT):
|
||||
"""
|
||||
使用 MIT 模式将电机从当前位置平滑回到零点
|
||||
duration: 总运动时间 (秒)
|
||||
dt: 控制周期 (秒)
|
||||
"""
|
||||
global motor1, motor2, motor_control, current_theta1, current_theta4
|
||||
|
||||
# 获取当前位置
|
||||
theta1_start, theta4_start = get_current_motor_position()
|
||||
# 计算步数
|
||||
steps = int(duration / dt)
|
||||
for i in range(steps + 1):
|
||||
t = i / steps
|
||||
# 线性插值
|
||||
theta1_target = theta1_start * (1 - t)
|
||||
theta4_target = theta4_start * (1 - t)
|
||||
# 发送 MIT 控制
|
||||
control_two_motors_mit(theta1_target, theta4_target)
|
||||
busy_wait(dt)
|
||||
|
||||
# 确保最终位置为零
|
||||
control_two_motors_mit(0.0, 0.0)
|
||||
current_theta1 = current_theta4 = 0.0
|
||||
print("电机已回零完成。")
|
||||
|
||||
# ==================== MIT 模式移动到指定角度（任意两点） =====================
|
||||
def move_motors_to_target(theta1_target_rad, theta4_target_rad, duration=1.0, dt=DT,
|
||||
theta1_start_rad=None, theta4_start_rad=None):
|
||||
"""
|
||||
使用 MIT 模式将电机从起点平滑移动到指定目标角度
|
||||
参数:
|
||||
theta1_target_rad: 电机1目标角度（弧度）
|
||||
theta4_target_rad: 电机4目标角度（弧度）
|
||||
duration: 总运动时间 (秒)
|
||||
dt: 控制周期 (秒)
|
||||
theta1_start_rad: 电机1起始角度（弧度），默认 None 表示从零点
|
||||
theta4_start_rad: 电机4起始角度（弧度），默认 None 表示从零点
|
||||
"""
|
||||
global motor1, motor2, motor_control, current_theta1, current_theta4
|
||||
|
||||
# 默认从零点出发
|
||||
if theta1_start_rad is None:
|
||||
theta1_start_rad = 0.0
|
||||
if theta4_start_rad is None:
|
||||
theta4_start_rad = 0.0
|
||||
|
||||
steps = int(duration / dt)
|
||||
for i in range(steps + 1):
|
||||
t = i / steps
|
||||
# 线性插值
|
||||
theta1_now = theta1_start_rad + (theta1_target_rad - theta1_start_rad) * t
|
||||
theta4_now = theta4_start_rad + (theta4_target_rad - theta4_start_rad) * t
|
||||
# 发送 MIT 控制
|
||||
control_two_motors_mit(theta1_now, theta4_now)
|
||||
busy_wait(dt)
|
||||
|
||||
# 确保最终位置精确到目标
|
||||
control_two_motors_mit(theta1_target_rad, theta4_target_rad)
|
||||
current_theta1 = theta1_target_rad
|
||||
current_theta4 = theta4_target_rad
|
||||
print(f"电机已移动到目标角度: θ1={np.degrees(theta1_target_rad):.2f}°, θ4={np.degrees(theta4_target_rad):.2f}°")
|
||||
|
||||
# --- 关节角度范围（仍显示整个过程）---
|
||||
if len(all_th1) > 0 and len(all_th4) > 0:
|
||||
print("\n=== 关节角度范围统计 ===")
|
||||
print(f"θ₁ 范围: {min(all_th1):.2f}° ~ {max(all_th1):.2f}°")
|
||||
print(f"θ₄ 范围: {min(all_th4):.2f}° ~ {max(all_th4):.2f}°")
|
||||
|
||||
# ------------------------ 主函数 ------------------------
|
||||
if __name__ == "__main__":
|
||||
try:
|
||||
# ---------------- 初始化电机 ----------------
|
||||
init_motors()
|
||||
|
||||
# 选择轨迹（可切换）
|
||||
# --- 获取当前位置测试 ---
|
||||
print("\n=== 测试：获取电机当前位置 ===")
|
||||
theta1, theta4 = get_current_motor_position()
|
||||
|
||||
# --- MIT 模式回零 ---
|
||||
print("\n=== MIT 模式回零 ===")
|
||||
move_motors_to_zero(duration=1.0) # 主函数里执行回零
|
||||
|
||||
# ---------------- 选择轨迹 ----------------
|
||||
trajectory_config = {
|
||||
'func': line_trajectory_fix,
|
||||
'params': {'start': (25, 300), 'end': (200, 300), 'num_points': 100}
|
||||
}
|
||||
|
||||
# 示例：圆形轨迹
|
||||
# trajectory_config = {
|
||||
# 'func': circle_trajectory,
|
||||
# 'params': {'center': (100, 300), 'radius': 40, 'num_points': 100}
|
||||
# }
|
||||
|
||||
run_trajectory_with_animation(trajectory_config['func'], **trajectory_config['params'])
|
||||
|
||||
except KeyboardInterrupt:
|
||||
@ -543,11 +468,9 @@ if __name__ == "__main__":
|
||||
print(f"程序异常: {e}")
|
||||
finally:
|
||||
if not DEBUG_MODE:
|
||||
try:
|
||||
motor_control.disable(motor1)
|
||||
motor_control.disable(motor2)
|
||||
print("电机已停机。")
|
||||
except Exception:
|
||||
pass
|
||||
motor_control.disable(motor1)
|
||||
motor_control.disable(motor2)
|
||||
print("电机已停机。")
|
||||
else:
|
||||
print("【DEBUG】程序结束")
|
||||
|
||||
|
||||
130
mian_test.py
Normal file
130
mian_test.py
Normal file
@ -0,0 +1,130 @@
|
||||
import time
|
||||
import numpy as np
|
||||
import matplotlib.pyplot as plt
|
||||
from matplotlib.animation import FuncAnimation
|
||||
from time import perf_counter
|
||||
|
||||
# ------------------------ 调试开关 ------------------------
|
||||
DEBUG_MODE = False # True: 模拟电机, False: 真机
|
||||
|
||||
# ------------------------ 电机与控制 ------------------------
|
||||
if DEBUG_MODE:
|
||||
class MockMotor:
|
||||
def __init__(self):
|
||||
self._pos_deg = 45.0
|
||||
def getPosition(self):
|
||||
return self._pos_deg
|
||||
def setPosition(self, deg):
|
||||
self._pos_deg = deg
|
||||
print(f"[DEBUG] 电机位置 -> {deg:.2f}°")
|
||||
|
||||
class MockControl:
|
||||
def enable(self, m): return True
|
||||
def disable(self, m): return None
|
||||
def controlMIT(self, m, kp, kd, pos, vel, torq):
|
||||
deg = np.degrees(pos)
|
||||
m.setPosition(deg)
|
||||
|
||||
motor1 = MockMotor()
|
||||
motor2 = MockMotor()
|
||||
motor_control = MockControl()
|
||||
else:
|
||||
import serial
|
||||
from DM_CAN.DM_CAN import Motor, MotorControl, DM_Motor_Type, Control_Type
|
||||
|
||||
CAN_SERIAL_PORT = '/dev/ttyACM0'
|
||||
BAUD_RATE = 921600
|
||||
MOTOR1_ID = 0x01
|
||||
MOTOR2_ID = 0x02
|
||||
|
||||
def init_real_motors():
|
||||
try:
|
||||
can_serial = serial.Serial(CAN_SERIAL_PORT, BAUD_RATE, timeout=0.5)
|
||||
print(f"CAN 串口 {CAN_SERIAL_PORT} 打开成功")
|
||||
except Exception as e:
|
||||
print(f"无法打开串口: {e}")
|
||||
exit(1)
|
||||
|
||||
mc = MotorControl(can_serial)
|
||||
m1 = Motor(DM_Motor_Type.DM4310, MOTOR1_ID, 0x11)
|
||||
m2 = Motor(DM_Motor_Type.DM4310, MOTOR2_ID, 0x12)
|
||||
mc.addMotor(m1)
|
||||
mc.addMotor(m2)
|
||||
mc.switchControlMode(m1, Control_Type.MIT)
|
||||
mc.switchControlMode(m2, Control_Type.MIT)
|
||||
time.sleep(0.1)
|
||||
mc.save_motor_param(m1)
|
||||
mc.save_motor_param(m2)
|
||||
mc.enable(m1)
|
||||
mc.enable(m2)
|
||||
print("真实电机已使能。")
|
||||
return m1, m2, mc
|
||||
|
||||
# ------------------------ 通用函数 ------------------------
|
||||
def busy_wait(dt):
|
||||
start = perf_counter()
|
||||
while perf_counter() - start < dt:
|
||||
pass
|
||||
|
||||
def adjust_angle_continuity(new_angle, prev_angle):
|
||||
diff = new_angle - prev_angle
|
||||
while diff > np.pi:
|
||||
diff -= 2 * np.pi
|
||||
while diff < -np.pi:
|
||||
diff += 2 * np.pi
|
||||
return prev_angle + diff
|
||||
|
||||
def control_two_motors_mit(theta1_rad, theta4_rad, dt=0.01):
|
||||
motor_control.controlMIT(motor1, 50, 1, theta1_rad, 0.1, 0.0)
|
||||
motor_control.controlMIT(motor2, 50, 1, theta4_rad, 0.1, 0.0)
|
||||
busy_wait(dt)
|
||||
|
||||
# ------------------------ 移动到零点 ------------------------
|
||||
def move_to_zero_point(steps=60, dt=0.01):
|
||||
theta1_current = np.radians(motor1.getPosition())
|
||||
theta4_current = np.radians(motor2.getPosition())
|
||||
theta1_list = np.linspace(theta1_current, 0.0, steps)
|
||||
theta4_list = np.linspace(theta4_current, 0.0, steps)
|
||||
|
||||
for t1, t4 in zip(theta1_list, theta4_list):
|
||||
t1_adj = adjust_angle_continuity(t1, theta1_current)
|
||||
t4_adj = adjust_angle_continuity(t4, theta4_current)
|
||||
control_two_motors_mit(t1_adj, t4_adj, dt)
|
||||
|
||||
print("已到达零点。")
|
||||
print(f"电机1角度: {motor1.getPosition():.2f}°")
|
||||
print(f"电机2角度: {motor2.getPosition():.2f}°")
|
||||
|
||||
# ------------------------ 示例轨迹动画 ------------------------
|
||||
def draw_demo_trajectory():
|
||||
x_list = np.linspace(0, 200, 50)
|
||||
y_list = 100 + 50 * np.sin(np.linspace(0, 2*np.pi, 50))
|
||||
|
||||
fig, ax = plt.subplots(figsize=(8, 6))
|
||||
ax.set_xlim(-50, 250)
|
||||
ax.set_ylim(0, 250)
|
||||
ax.set_aspect('equal')
|
||||
ax.grid(True)
|
||||
ax.plot(x_list, y_list, 'b--', label='示例轨迹')
|
||||
line, = ax.plot([], [], 'ro-', lw=2, label='机械臂')
|
||||
|
||||
def update(i):
|
||||
line.set_data([0, x_list[i]], [0, y_list[i]])
|
||||
return line,
|
||||
|
||||
ani = FuncAnimation(fig, update, frames=len(x_list), interval=50, blit=True, repeat=False)
|
||||
ax.legend()
|
||||
plt.show()
|
||||
|
||||
# ------------------------ 主程序 ------------------------
|
||||
if __name__ == "__main__":
|
||||
if not DEBUG_MODE:
|
||||
motor1, motor2, motor_control = init_real_motors()
|
||||
else:
|
||||
print("【DEBUG模式】使用模拟电机")
|
||||
|
||||
print(f"当前电机角度 -> 电机1: {motor1.getPosition():.2f}°, 电机2: {motor2.getPosition():.2f}°")
|
||||
print("移动到零点...")
|
||||
move_to_zero_point(steps=60, dt=0.01)
|
||||
print("显示示例轨迹动画...")
|
||||
draw_demo_trajectory()
|
||||
Reference in New Issue
Block a user