测试only_line_main直线电机控制，main是移动到初始点再直线往返一次代码
This commit is contained in:
琉璃月光
378
only_line_main.py
Normal file
378
only_line_main.py
Normal file
@ -0,0 +1,378 @@
|
||||
# ==================== 五连杆机械臂轨迹控制（直接角度发送版）====================
|
||||
# 功能：轨迹生成 + 逆解 + 直接控制 + 动画显示 + 关节角度可视化 + FK 验证
|
||||
# ==============================================================================
|
||||
|
||||
import time
|
||||
import numpy as np
|
||||
import matplotlib.pyplot as plt
|
||||
from matplotlib.animation import FuncAnimation
|
||||
from time import perf_counter # 高精度计时
|
||||
|
||||
# 设置中文字体和负号显示
|
||||
plt.rcParams['font.sans-serif'] = ['SimHei', 'WenQuanYi Zen Hei', 'FangSong']
|
||||
plt.rcParams['axes.unicode_minus'] = False
|
||||
|
||||
# ------------------------ 调试开关 ------------------------
|
||||
DEBUG_MODE = False # <<< 设为 False 控制真实电机
|
||||
|
||||
# 导入运动学和轨迹函数（确保路径正确）
|
||||
try:
|
||||
from calculate.ik import inverseF
|
||||
from calculate.fk import forwardF
|
||||
from calculate.trajectory import (
|
||||
circle_trajectory,
|
||||
line_trajectory,
|
||||
line_trajectory_fix,
|
||||
ellipse_trajectory,
|
||||
square_trajectory,
|
||||
triangle_trajectory
|
||||
)
|
||||
except ImportError as e:
|
||||
print(f"【警告】无法导入运动学模块: {e}, 使用 DEBUG_MODE")
|
||||
DEBUG_MODE = True
|
||||
|
||||
# -------------------- 非 Debug 模式导入硬件库 --------------------
|
||||
if not DEBUG_MODE:
|
||||
try:
|
||||
from DM_CAN.DM_CAN import Motor, MotorControl, DM_Motor_Type, Control_Type
|
||||
import serial
|
||||
except ImportError as e:
|
||||
print(f"硬件库导入失败: {e}")
|
||||
exit(1)
|
||||
else:
|
||||
print("【DEBUG MODE】: 已启用调试模式，不连接真实硬件。")
|
||||
|
||||
# ------------------------ 机械臂参数 ------------------------
|
||||
L1 = 250 # 左臂长度 (mm)
|
||||
L2 = 300
|
||||
L3 = 300
|
||||
L4 = 250 # 右臂长度
|
||||
L0 = 250 # 基座右端偏移
|
||||
|
||||
# ------------------------ 电机与通信配置 ------------------------
|
||||
MOTOR1_ID = 0x01
|
||||
MOTOR2_ID = 0x02
|
||||
CAN_SERIAL_PORT = '/dev/ttyACM0'
|
||||
BAUD_RATE = 921600
|
||||
KP = 50.0
|
||||
KD = 1.0
|
||||
DT = 0.01 # 控制周期 10ms（每点延时）
|
||||
|
||||
# ------------------------ 全局变量 ------------------------
|
||||
motor1 = motor2 = motor_control = None
|
||||
current_theta1 = current_theta4 = 0.0
|
||||
x_list = y_list = [] # 轨迹点
|
||||
line = None
|
||||
|
||||
# ------------------------ 精确延时 ------------------------
|
||||
def busy_wait(dt):
|
||||
"""高精度延时"""
|
||||
start = perf_counter()
|
||||
while perf_counter() - start < dt:
|
||||
pass
|
||||
|
||||
# ------------------------ 角度连续性调整 ------------------------
|
||||
def adjust_angle_continuity(new_angle, prev_angle):
|
||||
"""
|
||||
防止角度跳变（如 3.14 → -3.14），保持连续
|
||||
"""
|
||||
diff = new_angle - prev_angle
|
||||
while diff > np.pi:
|
||||
diff -= 2 * np.pi
|
||||
while diff < -np.pi:
|
||||
diff += 2 * np.pi
|
||||
return prev_angle + diff
|
||||
|
||||
# ------------------------ 初始化电机 ------------------------
|
||||
def init_motors():
|
||||
global motor1, motor2, motor_control
|
||||
|
||||
if DEBUG_MODE:
|
||||
print("【DEBUG】跳过电机初始化")
|
||||
motor1 = motor2 = type('Motor', (), {'id': 0})()
|
||||
motor_control = type('MotorControl', (), {
|
||||
'enable': lambda x: True,
|
||||
'disable': lambda x: None,
|
||||
'controlMIT': lambda m, kp, kd, pos, vel, torq: None,
|
||||
'refresh_motor_status': lambda m: None,
|
||||
'switchControlMode': lambda m, mode: None,
|
||||
'save_motor_param': lambda m: None
|
||||
})()
|
||||
return motor1, motor2, motor_control
|
||||
|
||||
try:
|
||||
can_serial = serial.Serial(CAN_SERIAL_PORT, BAUD_RATE, timeout=0.5)
|
||||
print(f"CAN 串口 {CAN_SERIAL_PORT} 打开成功")
|
||||
except Exception as e:
|
||||
print(f"无法打开串口: {e}")
|
||||
exit(1)
|
||||
|
||||
motor_control = MotorControl(can_serial)
|
||||
motor1 = Motor(DM_Motor_Type.DM4310, MOTOR1_ID, 0x11)
|
||||
motor2 = Motor(DM_Motor_Type.DM4310, MOTOR2_ID, 0x12)
|
||||
|
||||
motor_control.addMotor(motor1)
|
||||
motor_control.addMotor(motor2)
|
||||
motor_control.switchControlMode(motor1, Control_Type.MIT)
|
||||
motor_control.switchControlMode(motor2, Control_Type.MIT)
|
||||
time.sleep(0.1)
|
||||
motor_control.save_motor_param(motor1)
|
||||
motor_control.save_motor_param(motor2)
|
||||
motor_control.enable(motor1)
|
||||
motor_control.enable(motor2)
|
||||
print("电机已使能。")
|
||||
return motor1, motor2, motor_control
|
||||
|
||||
# ------------------------ MIT 控制函数 ------------------------
|
||||
def control_two_motors_mit(theta1_rad, theta4_rad):
|
||||
"""
|
||||
发送 MIT 控制指令（角度单位：弧度）
|
||||
参数: theta1_rad, theta4_rad —— 目标角度（弧度）
|
||||
"""
|
||||
global current_theta1, current_theta4
|
||||
|
||||
# ✅ 直接使用弧度值，不再转为角度
|
||||
pos1 = theta1_rad
|
||||
pos4 = theta4_rad
|
||||
vel = 0.1
|
||||
torq = 0.0
|
||||
|
||||
if not DEBUG_MODE:
|
||||
motor_control.controlMIT(motor1, KP, KD, pos1, vel, torq)
|
||||
motor_control.controlMIT(motor2, KP, KD, pos4, vel, torq)
|
||||
else:
|
||||
# 仅用于调试打印，才转为角度
|
||||
print(f"[DEBUG] 控制 -> θ1={np.degrees(theta1_rad):.2f}°, θ4={np.degrees(theta4_rad):.2f}°")
|
||||
|
||||
current_theta1 = theta1_rad
|
||||
current_theta4 = theta4_rad
|
||||
|
||||
# ------------------------ 直接轨迹执行函数（无插值）------------------------
|
||||
from time import perf_counter
|
||||
import numpy as np
|
||||
|
||||
|
||||
# 假设其他所需函数和全局变量已定义，例如 inverseF, forwardF, adjust_angle_continuity, control_two_motors_mit, 等等.
|
||||
|
||||
def execute_direct_trajectory(x_list, y_list, dt=DT):
|
||||
"""
|
||||
直接执行轨迹：对每个 (x,y) 计算逆解并立即发送角度，不做任何插值或速度规划
|
||||
返回: (time_log, theta1_log, theta4_log, x_fk_log, y_fk_log)
|
||||
"""
|
||||
global motor_control, motor1, motor2
|
||||
|
||||
# 定义90度对应于弧度的偏移量
|
||||
ANGLE_OFFSET_RAD = np.pi / 2 # 即90度对应的弧度值
|
||||
|
||||
time_log = []
|
||||
theta1_log = []
|
||||
theta4_log = []
|
||||
x_fk_log = []
|
||||
y_fk_log = []
|
||||
|
||||
l1, l2, l3, l4, l5 = L1, L2, L3, L4, L0
|
||||
omega1 = omega4 = 0.0
|
||||
alpha1 = alpha4 = 0.0
|
||||
|
||||
# 获取当前角度（用于连续性调整）
|
||||
if not DEBUG_MODE:
|
||||
motor_control.refresh_motor_status(motor1)
|
||||
motor_control.refresh_motor_status(motor2)
|
||||
time.sleep(0.1)
|
||||
motor_control.refresh_motor_status(motor1)
|
||||
motor_control.refresh_motor_status(motor2)
|
||||
current_theta1 = np.radians(motor1.getPosition()) - ANGLE_OFFSET_RAD
|
||||
current_theta4 = np.radians(motor2.getPosition()) - ANGLE_OFFSET_RAD
|
||||
else:
|
||||
current_theta1 = current_theta4 = -ANGLE_OFFSET_RAD # 考虑到偏移
|
||||
|
||||
start_time = perf_counter()
|
||||
|
||||
for i, (x, y) in enumerate(zip(x_list, y_list)):
|
||||
try:
|
||||
# 计算逆解
|
||||
raw_theta1, raw_theta4 = inverseF(x, y, L1, L2, L3, L4, L0)
|
||||
|
||||
# 应用角度偏移
|
||||
target_theta1 = float(raw_theta1) - ANGLE_OFFSET_RAD
|
||||
target_theta4 = float(raw_theta4) - ANGLE_OFFSET_RAD
|
||||
|
||||
# 调整角度连续性
|
||||
target_theta1 = adjust_angle_continuity(target_theta1, current_theta1)
|
||||
target_theta4 = adjust_angle_continuity(target_theta4, current_theta4)
|
||||
|
||||
except Exception as e:
|
||||
print(f"第 {i} 点逆解失败 ({x:.2f}, {y:.2f}): {e}")
|
||||
# 保持上一角度
|
||||
target_theta1 = current_theta1
|
||||
target_theta4 = current_theta4
|
||||
else:
|
||||
current_theta1, current_theta4 = target_theta1, target_theta4
|
||||
|
||||
# === 直接发送角度到电机（假设motor api接受弧度值）===
|
||||
control_two_motors_mit(target_theta1, target_theta4)
|
||||
|
||||
# === FK 验证实际到达位置 ===
|
||||
try:
|
||||
xc, yc, _, _, _, _, _, _ = forwardF(
|
||||
u1=target_theta1 + ANGLE_OFFSET_RAD,
|
||||
u4=target_theta4 + ANGLE_OFFSET_RAD,
|
||||
omega1=omega1, omega4=omega4,
|
||||
l1=l1, l2=l2, l3=l3, l4=l4, l5=l5,
|
||||
alpha1=alpha1, alpha4=alpha4
|
||||
)
|
||||
x_fk_log.append(xc)
|
||||
y_fk_log.append(yc)
|
||||
except Exception as fk_e:
|
||||
x_fk_log.append(np.nan)
|
||||
y_fk_log.append(np.nan)
|
||||
|
||||
# 记录日志
|
||||
elapsed = perf_counter() - start_time
|
||||
time_log.append(elapsed)
|
||||
theta1_log.append(np.degrees(target_theta1)) # 将弧度转回角度以便记录
|
||||
theta4_log.append(np.degrees(target_theta4))
|
||||
|
||||
# 固定延时，控制发送频率
|
||||
busy_wait(dt)
|
||||
|
||||
return time_log, theta1_log, theta4_log, x_fk_log, y_fk_log
|
||||
|
||||
# ------------------------ 动画绘制函数 ------------------------
|
||||
def draw_frame(i):
|
||||
x = x_list[i]
|
||||
y = y_list[i]
|
||||
try:
|
||||
theta1, theta4 = inverseF(x, y, L1, L2, L3, L4, L0)
|
||||
x2 = L1 * np.cos(theta1)
|
||||
y2 = L1 * np.sin(theta1)
|
||||
x4 = L0 + L4 * np.cos(theta4)
|
||||
y4 = L4 * np.sin(theta4)
|
||||
x_coords = [0, x2, x, x4, L0]
|
||||
y_coords = [0, y2, y, y4, 0]
|
||||
line.set_data(x_coords, y_coords)
|
||||
except:
|
||||
line.set_data([], [])
|
||||
return line,
|
||||
|
||||
# ------------------------ 轨迹动画与执行 + 可视化 + FK 验证 ------------------------
|
||||
def run_trajectory_with_animation(trajectory_func, **params):
|
||||
global x_list, y_list, line
|
||||
|
||||
print(f"生成轨迹: {trajectory_func.__name__}")
|
||||
x_list, y_list = trajectory_func(**params)
|
||||
print(f"轨迹点数: {len(x_list)}")
|
||||
|
||||
# --- 动画 ---
|
||||
fig, ax = plt.subplots(figsize=(10, 8))
|
||||
ax.set_xlim(-50, L0 + 100)
|
||||
ax.set_ylim(0, 500)
|
||||
ax.set_aspect('equal')
|
||||
ax.grid(True, alpha=0.6)
|
||||
ax.set_title(f"五连杆机械臂 - 轨迹: {trajectory_func.__name__}")
|
||||
|
||||
ax.plot(x_list, y_list, 'b--', alpha=0.5, label='目标轨迹')
|
||||
line, = ax.plot([], [], 'r-o', lw=3, ms=6, label='机械臂')
|
||||
ax.legend()
|
||||
|
||||
ani = FuncAnimation(fig, draw_frame, frames=len(x_list),
|
||||
interval=50, blit=True, repeat=False)
|
||||
plt.show()
|
||||
|
||||
# --- 执行并记录 ---
|
||||
print("开始执行轨迹（直接发送角度）...")
|
||||
time_log, theta1_log, theta4_log, x_fk_log, y_fk_log = execute_direct_trajectory(
|
||||
x_list, y_list, dt=DT # 每个点发送后延时 1ms，这个地方控制电机延时
|
||||
)
|
||||
|
||||
# --- 绘制关节角度 ---
|
||||
fig2, (ax1, ax2) = plt.subplots(2, 1, figsize=(10, 6), sharex=True)
|
||||
ax1.plot(time_log, theta1_log, 'b-o', markersize=3, linewidth=1.5, label='θ₁ (电机1)')
|
||||
ax1.set_ylabel('关节角 θ₁ (°)')
|
||||
ax1.set_title('电机关节角度随时间变化')
|
||||
ax1.grid(True, alpha=0.5)
|
||||
ax1.legend()
|
||||
|
||||
ax2.plot(time_log, theta4_log, 'r-o', markersize=3, linewidth=1.5, label='θ₄ (电机2)')
|
||||
ax2.set_xlabel('时间 (秒)')
|
||||
ax2.set_ylabel('关节角 θ₄ (°)')
|
||||
ax2.grid(True, alpha=0.5)
|
||||
ax2.legend()
|
||||
plt.tight_layout()
|
||||
plt.show()
|
||||
|
||||
# --- FK 验证 ---
|
||||
fig3, ax3 = plt.subplots(figsize=(10, 8))
|
||||
ax3.plot(x_list, y_list, 'b--', linewidth=2, label='目标轨迹', alpha=0.8)
|
||||
ax3.plot(x_fk_log, y_fk_log, 'g-', linewidth=2, marker='o', markersize=3, label='FK 重建轨迹', alpha=0.7)
|
||||
ax3.scatter(x_fk_log[0], y_fk_log[0], c='green', s=100, marker='s', label='起点')
|
||||
ax3.scatter(x_fk_log[-1], y_fk_log[-1], c='red', s=100, marker='x', label='终点')
|
||||
ax3.set_xlabel('X (mm)')
|
||||
ax3.set_ylabel('Y (mm)')
|
||||
ax3.set_title('FK 验证：目标 vs 实际轨迹')
|
||||
ax3.grid(True, alpha=0.5)
|
||||
ax3.legend()
|
||||
ax3.set_aspect('equal')
|
||||
plt.tight_layout()
|
||||
plt.show()
|
||||
|
||||
# --- 误差统计 ---
|
||||
mask = ~np.isnan(x_fk_log) & ~np.isnan(y_fk_log)
|
||||
x_fk_valid = np.array(x_fk_log)[mask]
|
||||
y_fk_valid = np.array(y_fk_log)[mask]
|
||||
if len(x_fk_valid) == 0:
|
||||
print("【警告】FK 数据全为 nan，无法计算误差")
|
||||
return
|
||||
|
||||
# 插值对齐长度
|
||||
t_target = np.linspace(0, 1, len(x_list))
|
||||
t_fk = np.linspace(0, 1, len(x_fk_valid))
|
||||
from scipy.interpolate import interp1d
|
||||
try:
|
||||
f_x = interp1d(t_fk, x_fk_valid, kind='linear', fill_value='extrapolate')
|
||||
f_y = interp1d(t_fk, y_fk_valid, kind='linear', fill_value='extrapolate')
|
||||
x_interp = f_x(t_target)
|
||||
y_interp = f_y(t_target)
|
||||
errors = np.sqrt((x_interp - x_list)**2 + (y_interp - y_list)**2)
|
||||
print("\n=== FK 验证误差统计 ===")
|
||||
print(f"平均误差: {np.mean(errors):.3f} mm")
|
||||
print(f"最大误差: {np.max(errors):.3f} mm")
|
||||
print(f"标准差: {np.std(errors):.3f} mm")
|
||||
except Exception as e:
|
||||
print(f"误差计算失败: {e}")
|
||||
|
||||
# --- 关节角度范围 ---
|
||||
print("\n=== 关节角度范围统计 ===")
|
||||
print(f"θ₁ 范围: {min(theta1_log):.2f}° ~ {max(theta1_log):.2f}°")
|
||||
print(f"θ₄ 范围: {min(theta4_log):.2f}° ~ {max(theta4_log):.2f}°")
|
||||
|
||||
# ------------------------ 主函数 ------------------------
|
||||
if __name__ == "__main__":
|
||||
try:
|
||||
init_motors()
|
||||
|
||||
# 选择轨迹（可切换）
|
||||
trajectory_config = {
|
||||
'func': line_trajectory_fix,
|
||||
'params': {'start': (25, 300), 'end': (200, 300), 'num_points': 100}
|
||||
}
|
||||
|
||||
# 示例：圆形轨迹
|
||||
# trajectory_config = {
|
||||
# 'func': circle_trajectory,
|
||||
# 'params': {'center': (100, 300), 'radius': 40, 'num_points': 100}
|
||||
# }
|
||||
|
||||
run_trajectory_with_animation(trajectory_config['func'], **trajectory_config['params'])
|
||||
|
||||
except KeyboardInterrupt:
|
||||
print("\n【用户中断】")
|
||||
except Exception as e:
|
||||
print(f"程序异常: {e}")
|
||||
finally:
|
||||
if not DEBUG_MODE:
|
||||
motor_control.disable(motor1)
|
||||
motor_control.disable(motor2)
|
||||
print("电机已停机。")
|
||||
else:
|
||||
print("【DEBUG】程序结束")
|
||||
Reference in New Issue
Block a user